A burst pipe does not announce itself politely. It splits open at 2 a.m. during a cold snap, and by morning you have water pouring through a ceiling, soaked drywall, and a restoration bill that makes the cost of prevention look like pocket change. Frozen pipes are one of the most common and most expensive winter home disasters, and nearly all of them are preventable.
Winterizing your pipes is a weekend project, not a renovation. With some foam insulation, a few valve turns, and the right thermostat habits, you can get through the coldest months without a plumbing emergency. This guide covers the full checklist: insulating exposed pipes, shutting down outdoor water, protecting indoor lines, and what to do if you are leaving the house empty for winter.
If a pipe has already burst on you before, you know the aftermath is the expensive part. Our guide on burst pipe water damage explains what the cleanup and repair process actually involves, which is good motivation to do the prevention work now.
Know your freeze risk and when to start
Pipes begin to freeze when temperatures drop into the low 20s Fahrenheit and stay there for several hours, especially overnight. Unheated spaces are the danger zones: crawl spaces, attics, garages, exterior walls, and anywhere plumbing runs near the outside of the house.
Start your winterizing work in the fall, well before the first hard freeze. In northern states that means October; in milder regions, late November is usually fine, but an early cold snap can catch anyone. Check the forecast habitually once nighttime lows start flirting with freezing, because a single surprise night in the teens can split an unprotected pipe.
Not all pipes are equally vulnerable. Copper and steel pipes conduct cold efficiently and freeze faster than PEX, which can expand slightly without bursting. But PEX fittings are still metal, and they can crack, so do not treat any plumbing as freeze-proof.
Insulate every exposed pipe you can reach
Insulation is the single highest-value step in winterizing. Foam pipe sleeves cost a dollar or two per six-foot length at any hardware store, slide on in seconds, and dramatically slow heat loss from the pipe.
Where to insulate first
Prioritize pipes in unheated areas: basements, crawl spaces, attics, garages, and under sinks on exterior walls. Also insulate any pipe that runs through an exterior wall cavity you can access. Hot water lines benefit too, because insulation reduces heat loss and your water heater works less, but cold water lines are the freeze priority.
How to install it properly
Measure the pipe diameter first, since sleeves come in standard sizes and a loose fit defeats the purpose. Cut the sleeve to length with a utility knife, open the pre-cut slit, and press it around the pipe. Tape the seams and joints with duct tape or the self-sealing strips on higher-end sleeves. Pay special attention to elbows and valves, which are common freeze points; use mitered pieces or wrap them with fiberglass pipe wrap and tape.
For the most exposed runs, consider electric heat tape or heat cable as a supplement. These wrap around the pipe and plug in, providing gentle warmth during extreme cold. Buy only UL-listed heat tape, follow the spacing instructions exactly, and never overlap the tape over itself, which creates hot spots and fire risk.
Shut off and drain your outdoor water lines
Outdoor spigots and irrigation lines are the most common freeze casualties because people forget them. A hose left connected to a spigot traps water in the line, and that trapped water expands when it freezes, cracking the pipe inside the wall where you cannot see it.
- Disconnect every hose. Drain them, coil them, and store them in the garage or shed. This alone prevents a large share of spigot failures.
- Shut off the interior valve. Most outdoor spigots have a shutoff valve inside the house, often in the basement or crawl space near where the line exits. Turn it off.
- Open the outdoor spigot. With the interior valve closed, open the outside spigot and let any remaining water drain out. Leave it open for winter so any residual water has room to expand.
- Drain the line if there is a bleeder cap. Many shutoff valves have a small bleeder cap; place a bucket under it, open it, and let the line drain completely, then close the cap.
- Winterize irrigation systems. Underground sprinkler lines need to be blown out with compressed air, which usually means hiring an irrigation company for $75 to $150. Skipping this step is how people discover cracked sprinkler heads and split lines in April.
If your spigots are the frost-free type with a long stem that shuts off deep inside the warm wall, they still need hoses disconnected, but they do not need the interior shutoff routine. Standard spigots need the full treatment.
Protect the pipes inside your house
Indoor plumbing usually survives winter on its own, but certain spots need attention, especially during extreme cold snaps or if your heating is unreliable.
Open cabinet doors on exterior walls
Kitchen and bathroom sinks on exterior walls hide pipes in closed cabinets that stay much colder than the room. Opening the cabinet doors lets warm room air circulate around the plumbing. If you have small children or pets and worry about cleaning products under the sink, move the products rather than closing the doors.
Keep the thermostat steady
Set the thermostat to at least 55 degrees Fahrenheit and keep it there day and night during cold weather. The money saved by dropping to 50 overnight is trivial compared to a burst pipe. If you have a smart thermostat, set a low-temperature alert so you know if the furnace fails while you are away.
Let faucets drip during extreme cold
When temperatures plunge into the teens or single digits, let faucets served by vulnerable pipes drip slowly, about five drops per minute. Moving water is much harder to freeze than still water. The slight increase in your water bill is nothing next to the cost of a burst line. Focus on faucets at the far ends of the plumbing run and any served by exterior-wall pipes.
Seal air leaks near plumbing
Cold air blowing directly on a pipe through a gap in the siding, foundation, or rim joist can freeze it even when the rest of the house is warm. Seal gaps around where pipes enter the house with caulk or expanding foam. This is also a good time to check for hidden moisture problems; our guide on how to find a hidden water leak covers the signs that water has already been getting in somewhere it should not.
Leaving for winter: the full shutdown checklist
An empty house in winter is a burst pipe waiting to happen, because nobody is there to notice the furnace failed. If you are leaving for weeks or months, do more than just set the thermostat.
- Shut off the main water supply and open the lowest faucet in the house to drain the lines. With no water pressure in the pipes, there is nothing to burst out.
- Drain the water heater or at least turn it to vacation mode. If you shut off the main, turn the water heater off entirely so it does not burn out trying to heat an empty tank.
- Add antifreeze to drains and toilets. Pour RV-grade (non-toxic) antifreeze into sink traps, tub drains, and toilet bowls to keep the trap water from freezing and cracking the fixtures.
- Keep the heat at 55 degrees minimum. Even with the water off, you want to protect the structure, appliances, and anything with residual water.
- Have someone check the house. A neighbor, friend, or house-check service visiting weekly can catch a furnace failure, and many insurance policies require regular checks for a vacant home to remain covered.
- Shut off the ice maker and washing machine valves individually as well, since appliance supply lines are a separate failure point from the main plumbing.
If a pipe freezes anyway: thaw it safely
A frozen pipe announces itself as a faucet that produces nothing, or a section of pipe with frost on the outside. Act quickly, because a frozen pipe is a burst pipe in waiting.
First, open the faucet the pipe supplies, so melting water has somewhere to go. Then warm the frozen section gently: a hair dryer on low, an electric heating pad wrapped around the pipe, or towels soaked in hot water. Start from the faucet end and work back toward the frozen section, so steam and pressure can escape. Never use an open flame, a torch, or a propane heater on a pipe; that is how houses catch fire.
If the pipe has already burst, shut off the main water immediately and call a plumber. Then start the drying process fast, because mold can begin growing on wet materials within a day or two. Keeping basement humidity under control afterward matters too; see our guide on preventing basement mold and our picks for the best basement dehumidifier for the drying phase.
Restoration professionals follow IICRC standards for structural drying after water events, which specify measured drying targets rather than guesswork, a useful benchmark if you ever hire out the cleanup, per the IICRC. FEMA also maintains winter preparedness resources for homeowners at fema.gov.
Frequently Asked Questions
At what temperature do pipes freeze?
Pipes can start freezing when temperatures drop to about 20 degrees Fahrenheit and stay there for six hours or more. Wind chill on exposed pipes and unheated spaces can cause freezing at higher air temperatures. The standard advice is to take precautions whenever overnight lows are forecast near or below freezing.
Is it better to drip hot or cold faucets?
Drip the cold water side. Hot water lines are actually more prone to freezing first in some conditions, but the goal is simply to keep water moving through the vulnerable pipe, and the cold line serves that purpose with less energy waste. If both lines run through an unheated area, dripping both is the safer choice.
How much does it cost to winterize pipes?
DIY winterizing typically costs $30 to $100 in materials: foam sleeves, tape, faucet covers, and caulk. A plumber doing a full winterization, including blowing out irrigation lines, usually charges $150 to $400. Compare that to the average burst pipe claim, which runs into the thousands once water damage and drying are included.
Do I need to winterize pipes in a mild climate?
Yes, arguably more so. Homes in mild climates often have plumbing in attics, crawl spaces, and exterior walls with minimal insulation, because builders never expected hard freezes. A single unusual cold snap does more damage in these regions precisely because nobody prepared.
Can PEX pipes burst from freezing?
PEX is more freeze-tolerant than copper because it can expand slightly, but it is not freeze-proof. The metal fittings and connections in a PEX system can still crack, and repeated freeze-thaw cycles weaken the pipe over time. Insulate PEX the same way you would any other plumbing.
Should I turn off my water if I lose heat in winter?
If your furnace dies during freezing weather and you cannot get it repaired quickly, shutting off the main water supply and draining the lines is smart damage control. Open the lowest faucet to drain, and call for heating repair immediately. A plumber can also advise on whether to drain the water heater.
The bottom line
Winterizing pipes is one of the cheapest insurance policies a homeowner can buy: a Saturday afternoon, under a hundred dollars in materials, and a burst pipe disaster that never happens. Insulate the exposed runs, disconnect the hoses, keep the heat steady, and have a plan for the house when you travel.
Do the work before the first freeze, not during it. Once temperatures drop into the teens, the hardware store sells out of foam sleeves, plumbers book out for days, and every unprotected pipe in your house is on a countdown.
